Paperboard Packaging Food Contact Migration Testing Rules

Paperboard food packaging compliance hinges on matching extraction tests to actual filling conditions and securing complete chemical inventory disclosures.

07.11.26 13 min

Statute

European packaging legislation does not treat paper and board like synthetic polymers. Plastics fall under harmonised rules in Commission Regulation 10/2011, but fibrous cellulose substrates have no dedicated EU-wide measure. For folding boxboard, solid bleached sulphate, and recycled cartonboard, compliance comes down to the overarching safety mandate of Regulation 1935/2004 and a patchwork of national guidance.

Under Article 3 of Regulation 1935/2004, food-contact materials must not transfer constituents to food in amounts that threaten human health, alter food composition unacceptably, or impair organoleptic properties. Because the EU sets no specific paper migration limits, national bodies and commercial buyers rely on German Federal Institute for Risk Assessment Recommendation XXXVI, the French DGCCRF Information Notice, and Council of Europe Resolution CM/Res(2020)9. These documents set positive substance lists, raw material purity criteria, and extraction caps.

European Regulation 1935/2004 penalizes packaging releases that endanger human health or bring about an unacceptable deterioration in organoleptic characteristics.

Cellulose fibres form porous, hydrophilic capillary networks with non-uniform structure. That open network allows both liquid absorption and vapor transport, setting paperboard apart from extruded plastic barriers. German BfR Recommendation XXXVI sets limits on manufacturing aids, slimicides, sizing agents, and synthetic sizing resins in food-contact paper and board.

BfR XXXVI/1 covers cooking papers and hot filter sheets, while BfR XXXVI/2 applies to baking papers. Under BfR XXXVI, dry matter extracted from the finished board must stay within explicit caps: formaldehyde cannot exceed 1.0 milligram per decimeter squared, glyoxal is restricted to 1.5 milligrams per decimeter squared, and water-soluble hexavalent chromium remains forbidden below detection limits of 0.005 milligrams per decimeter squared.

Paperboard Food Contact Regulatory Limits by Jurisdictional Source
Regulating Body Normative Reference Primary Contaminant Scope Enforcement Threshold Application Matrix
BfR Germany Recommendation XXXVI Aqueous extracts and slimicides Formaldehyde under 1.0 mg/dm² Direct contact paper and board
DGCCRF France Information Notice 2004-64 Heavy metals and volatile organic compounds Lead under 3.0 mg/kg substrate Aqueous and fatty food packaging
Council of Europe CM/Res(2020)9 MOSH and MOAH mineral oil fractions MOAH under 0.50 mg/kg food simulant Virgin and recovered fibre cartons
US FDA 21 CFR 176.170 Chloroform-soluble extractives Net extractives under 0.50 mg/in² Aqueous and fatty food contact
US FDA 21 CFR 176.180 Dry food extractive residues Positive list raw material verification Dry non-fatty contact sheets

In the United States, Title 21 of the Code of Federal Regulations sets the rules for paperboard. Section 176.170 lists permitted chemicals for paper and paperboard touching aqueous or fatty foods, alongside chloroform extraction limits, while Section 176.180 covers dry food contact. Under 21 CFR 176.170, exposing the finished sheet to distilled water at 121 degrees Celsius for two hours must yield no more than 0.5 milligrams of total chloroform-soluble extractives per square inch of food-contact surface.

The same 0.5 milligram ceiling applies after thirty minutes in n-heptane at 66 degrees Celsius for fatty food models. Buyers working across transatlantic supply chains have to manage these conflicting test methods: a European report based on EN 645 room-temperature water elution gives an FDA inspector demanding a two-hour reflux extractive under 21 CFR 176.170 nothing usable.

Specification clause 4.2 ties invoice payment directly to validated substance declarations, placing full responsibility for toxicological compliance on the converter.

Extract

Testing laboratories measure chemical transfer from cellulosic matrices using standardized water, solvent, and solid-phase extractions. Because plain paperboard lacks a molten sealing layer, tests often measure total extractable substances across the whole sheet rather than true surface partition kinetics. European standard EN 645 covers cold water extraction, soaking five grams of cut board strips in 250 milliliters of distilled water at twenty-three degrees Celsius for twenty-four hours to measure water-soluble compounds that leach during room-temperature contact with moist, non-fatty foods.

For hot liquids or baking, laboratories turn to EN 647, which circulates boiling water through the sample for two hours at eighty degrees Celsius to pull out polar additives, retention aids, and starch binders.

A cold water extraction conducted under EN 645 yields a formaldehyde limit below 1.0 milligram per decimeter squared after twenty-four hours at twenty-three degrees Celsius.

Liquid simulants like 3 percent acetic acid, 10 percent ethanol, or 95 percent ethanol can break down the cellulose web when modeling dry and fatty food migration, causing fibre sloughing that skews gravimetric measurements even when sizing agents resist edge penetration. To avoid this, testing relies on poly(2,6-diphenyl-p-phenylene oxide), sold as Tenax and standardized under EN 14338. Tenax acts as a porous synthetic adsorbent.

Granules are placed directly against the board’s food-contact face in a test cell and held under set thermal conditions ~ such as ten days at forty degrees Celsius for room-temperature storage or two hours at one hundred degrees Celsius for heating. The granules capture volatile and semi-volatile migrants emerging from the fibres; after exposure, the lab elutes the Tenax with diethyl ether or acetone and runs the concentrate through gas chromatography with flame ionization or mass spectrometry detection.

Rigid glass containers travel along an automated conveyor beneath a vertical dispensing tube filled with food product inside a converting facility.

Where Do Aqueous Extractions Break Down?

Unsealed edges on cut board samples pull liquid into inner unbleached or groundwood plies through capillary action. When technicians submerge bare coupons straight into test liquids, this edge wicking releases chemical fractions that would stay locked inside a finished package with folded edges. Total immersion produces artificially high migrant readings, so testing labs use single-sided contact cells that expose only the functional food-contact liner.

Fatty food testing is harder still: liquid triglycerides swell hydrophobic sizing agents, while simulants like vegetable oil or isooctane soak into the sheet quickly, pulling out optical brighteners, biocides, and wet-strength resins that clutter chromatograms with background noise.

Paperboard Extraction Standards and Target Analytical Classes
Standard Extracting Medium Thermal Exposure Primary Target Substances Detection Technique
EN 645 Deionized cold water 23°C for 24 hours Formaldehyde, glyoxal, soluble heavy metals Photometry and ICP-MS
EN 647 Deionized hot water 80°C for 2 hours Wet-strength resins, aziridines, melamine Liquid chromatography
EN 15519 Water and organic solvents Thermostatic bath Total dry matter of water extractives Gravimetric analysis
EN 14338 Tenax solid adsorbent 40°C to 175°C MOSH, MOAH, photoinitiators, plasticizers GC-FID and GC-MS
ISO 15320 Organic solvent extraction Soxhlet reflux Pentachlorophenol and polychlorinated phenols GC-ECD detection

Accredited paperboard migration testing follows a strict sequence to prevent lab contamination.

  1. Substrate conditioning stabilizes the fibrous sheet within a climate chamber maintained at twenty-three degrees Celsius and fifty percent relative humidity for forty-eight hours.
  2. Specimen isolation punches disk swatches from the conditioned sheet while avoiding folded score lines, watermarks, or operator handling margins.
  3. Single-sided cell loading seals the board against a polished stainless-steel migration flange, compressing the outer perimeter with food-grade fluoroelastomer gaskets.
  4. Thermal challenge execution places the loaded extraction apparatus into a calibrated convection oven running the exact temperature-time profile of the targeted food contact.
  5. Solvent elution concentration strips adsorbed target analytes off the recovery medium, followed by rotary evaporation under nitrogen to a precise quantitative volume.

Low detection limits require pure solvents and negative analytical blanks alongside every test run; without them, phthalates from room air or plastic tubing will skew the chromatogram. Buyers should verify that test reports specify single-sided cell testing rather than total immersion, which can inflate extracted dry matter on unvarnished folding board by up to four hundred percent.

Polar liquid simulants overstate penetration, whereas solid polymer adsorbents capture volatile compounds without breaking down the sheet structure.

Ink

Printing on the outside of a folding carton creates real migration risks for the unprinted interior. Sheetfed offset inks use hydrocarbon distillates, vegetable oils, resins, and metal driers for fast drying. As printed sheets come off the press, they stack under heavy pressure on pallets, pressing the wet varnish of one sheet tightly against the food-contact reverse side of the sheet above it.

This transfer, called set-off migration, deposits photoinitiators, plasticizers, and mineral oils onto the food-contact face before the board is ever converted into cartons ~ bypassing through-sheet diffusion completely.

A technician operates specialized laboratory equipment to prepare substrate cross sections for strict quality assurance evaluations.

Why Do Recycled Fibres Fail Mineral Oil Thresholds?

Recycled paper streams pull in newsprint, corrugated boxes, and flyers printed with standard inks. Mechanical de-inking washes off surface pigments but leaves short-chain mineral oils trapped in the pulp. These petroleum fractions divide into mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH).

The German Draft Mineral Oil Ordinance and EFSA classify MOAH with three or more aromatic rings as genotoxic carcinogens. Virgin kraft pulps show far lower background contamination than de-inked fiber: recovered white lined chipboard routinely carries baseline MOSH levels of 150 to 800 milligrams per kilogram of dry board and MOAH levels between 15 and 90 milligrams per kilogram ~ figures well above European food migration limits.

Virgin kraft pulps maintain lower baseline chromatographic contamination than de-inked recovered fiber furnish.

In dry food packaging for pasta, flour, or oatmeal, mineral oils with carbon chains from C10 to C24 evaporate out of the board at room temperature. Over twelve to thirty-six months of shelf life, these vaporized hydrocarbons move through the carton headspace and condense into the food. High-barrier inner bags, like biaxially oriented polypropylene or metallized polyethylene terephthalate, stop this gas-phase movement.

Packing dry food directly against untreated recycled board without a barrier pushes mineral oil contamination past safe limits.

  • Benzophenone photoinitiators migrate through set-off pressure stacks, displaying migration levels up to 2.5 milligrams per kilogram when curing lamps run below nominal wattage.
  • Primary aromatic amines originate from azo pigments used in yellow and red printing inks, presenting mutagens restricted to sum totals below 0.01 milligrams per kilogram of food.
  • Phthalate plasticizers leach from lamination adhesives and water-based dispersion varnishes, accumulating inside fatty foods through direct solvent partition.
  • Bisphenol derivatives transfer from epoxy can coatings and recycled thermal paper receipts, facing strict non-detection limits under modern European risk evaluations.

Measuring mineral oils requires online coupled liquid chromatography with gas chromatography and flame ionization detection (LC-GC-FID). The liquid chromatography column uses silver-nitrate-modified silica gel to separate MOSH from MOAH fractions, while the gas chromatography stage resolves carbon chains from C10 to C50. Results are reported as an integrated hump for the unresolved complex mixture.

If an accredited lab finds an unresolved MOAH hump between C10 and C25 exceeding 0.50 milligrams per kilogram of food, supermarket chains in Germany, France, and the Netherlands will reject the shipment.

Background levels of saturated hydrocarbons stem from mechanical lubricants across paper machine drying cylinders.

A digital render features a mechanical testing frame alongside stacked corrugated board sheets and geometric blocks inside a dark studio.

Liner

Converters use chemical sizing, water-based dispersions, and polymer laminates to block grease, water, and chemical migration. Extruded low-density polyethylene forms a liquid-tight barrier for milk cartons and liquid packaging board, preventing water loss during cold-water extraction. But polyolefin films lack tight molecular packing: mineral oils and volatile hydrocarbons pass straight through low-density polyethylene, which offers virtually no barrier to MOSH and MOAH during room-temperature storage.

Barrier Substrates and Migration Transmission Resistance
Barrier Construction Layer Thickness Grease Resistance (Kit Value) MOSH/MOAH Barrier Status Per- and Polyfluoroalkyl Substances Presence
Standard Solid Bleached Board 350 µm Kit 0 to 1 Zero barrier; volatile migration permitted None detected
Fluorochemical Surface Sizing 1 to 2 g/m² Kit 8 to 12 Grease repellent only; zero vapor barrier High target legacy presence
Water-based Acrylic Dispersion 6 to 12 g/m² Kit 6 to 9 Moderate barrier depending on coat weight Absent in certified formulations
Extruded LDPE Film 15 to 25 µm Kit 12 Zero vapor barrier to mineral hydrocarbons None detected
Metallized PET Lamination 12 µm Kit 12 Absolute functional barrier to all migrants None detected

Paper mills historically added fluorochemical sizing at the size press to make board oil- and water-resistant without ruining recyclability. These per- and polyfluoroalkyl substances (PFAS) rely on carbon-fluorine bonds that withstand heat, enzymes, and chemical breakdown, but short-chain perfluoroalkyl acids and fluorotelomer alcohols migrate into hot, fatty foods. Denmark banned PFAS in food-contact paper and board in 2020, setting a total organic fluorine limit of 20 milligrams per kilogram of dry board.

Broader EU rules under REACH Annex XVII and the proposed Universal PFAS Restriction cover any substance with at least one fully fluorinated methyl or methylene carbon. Buyers verify PFAS compliance using combustion ion chromatography for total fluorine, followed by liquid chromatography with tandem mass spectrometry to pinpoint individual perfluorinated carboxylic acids.

Water-based acrylic, latex, or biopolymer dispersions offer an easily recyclable alternative to extruded films, but folding and die-cutting put heavy mechanical stress on the coating. When score lines crack along carton corners, migrants pass straight through microscopic fractures in the surface layer. Because of this, testing labs have to evaluate finished, folded cartons rather than flat swatches ~ a flat sample can show perfect barrier integrity while the scored carton fails under the exact same test conditions.

Whether low molecular weight fluorinated oligomers migrate through dense biopolymer dispersions during high-temperature hot filling remains a point of debate among commercial testing labs.

A white paper carton sits on a grey surface next to a black tray holding liquid and a paper insert, adjacent to a sample display organizer.

Ledger

A Declaration of Compliance bridges lab test reports, customs clearance, and commercial supply contracts. Under Article 16 of Regulation 1935/2004, materials under specific measures need written proof of compliance, and European enforcement agencies require similar documentation for paperboard covering raw material origin, test parameters, and positive-list listings. Buyers need to confirm that declarations list the exact trade grade, grammage, coating layout, and approved food types; broad claims of food-safety compliance that omit test simulants, temperature caps, or surface-to-volume ratios will not stand up in an audit.

A declaration of compliance loses legal validity the moment converting lines introduce unlisted solvent inks.

The technical dossier standing behind a paperboard Declaration of Compliance must contain concrete analytical evidence, toxicological assessments of non-intentionally added substances, and trace supply chain records.

  • Chemical identity documentation catalogs all intentionally added substances, sizing agents, retention chemicals, biocides, and processing aids alongside their CAS registry numbers.
  • Toxicological safety screening assesses non-intentionally added substances, breakdown products, and reaction byproducts against European Food Safety Authority threshold of toxicological concern concepts.
  • Simulant contact declarations state the surface-to-volume ratio applied during migration bench testing, typically standardized at six square decimeters per kilogram of food simulant.
  • Batch traceability records link physical master reel identification numbers directly to the converting run, pallet tracking tags, and warehouse dispatch paperwork.
  • Production hygiene logs verify compliance with Commission Regulation 2023/2006 on good manufacturing practice, documenting microbiological control and pest abatement across mill drying operations.

When containers of non-EU paperboard packaging land at European ports, inspectors demand verified test certificates before releasing the shipment. If an importer cannot produce a Declaration of Compliance backed by accredited third-party reports within twenty-four hours, customs puts the lot into quarantine. Storage, warehouse handling, and administrative demurrage fees quickly accumulate to between 180 and 450 euros per container per day, while emergency lab testing on impounded shipments can take up to three weeks for full Tenax incubation and chromatographic analysis.

Liability extends quickly into retail channels. Major European supermarket chains regularly audit packaging compliance files, and if private-label food arrives in cartons lacking dual-use additive disclosures or mineral oil screening, retailers will delist the product. Delisting brings immediate chargebacks for unsold stock, disposal fees, and contractual penalties.

Protecting working capital requires auditing test credentials before issuing purchase orders: a complete dossier must contain ISO/IEC 17025 lab accreditation certificates, quantified migration limits based on recognized risk assessments, and clear converting instructions to prevent off-label food contact.

Failing to match test conditions to actual end-use food contact leads to rejected pallets at the warehouse and lost shelf space.

Nomenclature

Total Organic Fluorine

Screening Metric ~ Quantitative determination of all organically bound fluorine atoms within a substrate acts as a comprehensive proxy for perfluorinated chemical treatments.

EN 645

Extraction Protocol ~ European standard en 645 provides a set of procedural requirements for the preparation of cold water extracts from paper and board materials intended for food contact applications.

Set-off Migration

Chemical Transfer ~ Moving ink components from the outer surface to the inner contact layer occurs when printed sheets are stacked or wound into rolls.

EN 14338

Migration Rating ~ Standard EN 14338 specifies a test method for determining the level of volatile organic compounds transferred from printed paper and board intended for food contact applications.

BfR Recommendation XXXVI

Food Contact ~ Paper grades and board materials for secondary packaging or direct food contact undergo testing against specific migration limits set by the German Federal Institute for Risk Assessment.

MOSH MOAH Analysis

Hydrocarbon Quantification ~ Chromatography protocols determine the total content of mineral oil saturated hydrocarbons and mineral oil aromatic hydrocarbons within a packaging substrate or food contact material.

Migration Limits

Threshold Standard ~ Statutory concentration boundaries define the maximum allowable quantity of chemical substances that may transfer from packaging materials into food items.

Declaration of Compliance

Legal Attestation ~ A written regulatory instrument attests that a food contact packaging material satisfies applicable chemical migration limits and safety standards throughout the supply chain.

Council of Europe CM/Res(2020)9

Regulatory Framework ~ Public safety guidelines in Europe establish rigorous purity standards for food contact materials made of paper and board.

Regulation 1935/2004

Material Compliance ~ Legal accountability for food contact surfaces resides within regulation 1935/2004, which mandates that materials intended for contact with foodstuffs remain chemically inert under foreseeable conditions.

Liquid Chromatography

Analytical Separation ~ High-resolution physical separation techniques utilizing liquid mobile phases measure non-volatile organic compounds and chemical migrants in paper and board packaging materials.

Barrier Dispersion Coating

Polymer Suspension ~ Aqueous chemical dispersions formulate synthetic or bio-based polymer particles suspended in water to provide functional liquid barriers across paperboard substrates.

What the firm knows, published

Expertise is a utility, not a secret. sentiention™ publishes its working knowledge as open reference: intelligence layer covering the materials it sources, the markets it enters, and the reference that serves both.