Standard Paperboard Chemical Migration Testing Protocols for Food Contact Packaging Compliance
Food contact paperboard compliance demands simulant-specific migration testing, GC-MS target analysis, and verified declarations of compliance.

Threshold
Article 3 of Regulation EC 1935/2004 sets the baseline legal requirement for food contact materials in Europe: packaging must not transfer constituents into food at levels that threaten human health, alter food composition unacceptably, or deteriorate organoleptic characteristics. Unlike plastics, which fall under Regulation EU 10/2011, paper and board lack a single harmonized EU directive. Specific chemical limits instead depend on national frameworks and advisory guidelines.
Paperboard substrates readily absorb volatile organic compounds.
In Europe, German BfR Recommendation XXXVI forms the primary benchmark for food-contact paper and board, detailing permitted pulps, refining aids, coating chemicals, and authorized additives. Specific extraction thresholds for residual substances are measured in cold water extracts (EN 645) and hot water extracts (EN 647). Under these methods, cadmium extractions cannot exceed 0.002 milligrams per kilogram of paper, lead stays below 0.1 milligrams per kilogram, and mercury remains under 0.005 milligrams per kilogram, while formaldehyde in water extracts is capped at 15 milligrams per kilogram of paperboard sample.
Council of Europe Resolution AP (2002)1 and its updated guidance add further rules for paperboard safety. Primary aromatic amines (PAAs) originating from polyurethanes or azo pigments face a combined migration limit of 0.01 milligrams per kilogram of food simulant, while individual carcinogenic amines must remain non-detectable at a limit of quantification of 0.002 milligrams per kilogram. Polycyclic aromatic hydrocarbons (PAHs) introduced via raw carbon black additives carry an upper bound of 0.1 milligrams per kilogram in the finished packaging material.
| Regulatory Authority | Standard Reference | Permitted Food Types | Primary Chemical Targets | Migration Ceiling Threshold |
|---|---|---|---|---|
| German BfR | BfR Recommendation XXXVI | Dry, Fatty, and Aqueous Foods | Lead, Cadmium, Formaldehyde, Glyoxal | Lead < 0.1 mg/kg extract; Formaldehyde < 15 mg/kg extract |
| US FDA | 21 CFR 176.170 / 176.180 | Aqueous, Fatty, and Dry Foods | Chloroform-Soluble Extractives | Total extractives < 0.5 mg/sq in (0.078 mg/cm²) |
| Council of Europe | Resolution AP (2002)1 | All Packaging Paperboard | Heavy Metals, Primary Aromatic Amines | PAAs < 0.01 mg/kg sum; Cadmium < 0.002 mg/kg |
| EU Commission | Regulation EC 1935/2004 Art. 3 | All Food Contact Articles | General Chemical Transfer | No transfer endangering human health or organoleptic quality |
In the United States, FDA regulations cover paperboard under 21 CFR 176.170 for aqueous and fatty foods and 21 CFR 176.180 for dry food contact. Demonstrating compliance involves measuring net chloroform-soluble extractives using specified solvents; for instance, exposure to n-heptane at 120 degrees Fahrenheit for 30 minutes must not yield extractives above 0.5 milligrams per square inch of contact surface. For dry food packaging, internal sizing agents, defoamers, and wet-strength chemicals must comply with the positive list in 21 CFR 176.180.
Clause 4.2 of BfR Recommendation XXXVI restricts recycled fibers from direct contact with fatty foods unless an approved functional barrier keeps chemical transfer below analytical detection thresholds.

Fiber
Wood pulping leaves cellulose matrices with intrinsic extractives and leftover processing chemicals. Unrefined virgin sulfate and sulfite pulps carry resin acids, fatty acids, and terpenes that can spoil food flavor or aroma if unmanaged. Recycled furnishes like deinked pulp (DIP) and old corrugated containers (OCC) introduce broader contaminant profiles from post-consumer waste, offset inks, flexographic varnishes, and adhesives.
Because recycled paperboard varies structurally, non-intentionally added substances (NIAS) require screening.
Using recycled fiber introduces inherent chemical risks to the substrate.
Mineral oil hydrocarbons are the main group of contaminants found in recycled paperboard. Mineral Oil Saturated Hydrocarbons (MOSH) cover carbon chain lengths from C10 to C35 and originate from offset printing ink distillates, waxes, and machinery lubricants. Mineral Oil Aromatic Hydrocarbons (MOAH), also spanning C10 to C35, contain highly alkylated aromatic rings linked to genotoxic carcinogenicity.
Volatile MOSH and MOAH fractions migrate via gas phase across internal air gaps directly into dry foods like grains and pasta held in secondary cartons.
Rosin size components continuously desorb into food simulants under elevated storage temperatures.
Photoinitiators from outer printing inks can transfer onto the food-contact side through set-off on the converting reel. Compounds like benzophenone, 4-methylbenzophenone, 2-isopropylthioxanthone (ITX), and 2,2-dimethoxy-2-phenylacetophenone (DMPA) pass quickly through uncoated paperboard stock. Phthalates such as dibutyl phthalate (DBP) and diisobutyl phthalate (DIBP) frequently persist in recycled board from legacy adhesives.
Meanwhile, poly- and perfluoroalkyl substances (PFAS) used for oil-and-grease resistance (OGR) break down during thermal drying to yield perfluorooctanoic acid (PFOA) and fluorotelomer alcohol (FTOH) degradation products.
- Mineral Oil Hydrocarbons transfer from recycled newspaper inks through gas-phase deposition into dry grain substrates.
- Fluorinated Sizing Compounds degrade under heat during thermoforming to yield free perfluorooctanoic acid congeners.
- Chloropropanols leach from cross-linked wet-strength resins when aqueous food simulants break down ester linkages.
- Photoinitiator Residues migrate through set-off mechanisms when un-cured UV inks press against the reverse food-contact side on the reel.
Wet-strength resins added to liquid-packaging paperboard introduce chloropropanol impurities. Polyamidoamine-epichlorohydrin (PAE) formulations leave residual traces of 1,3-dichloro-2-propanol (1,3-DCP) and 3-chloro-1,2-propanediol (3-MCPD). BfR Recommendation XXXVI caps 3-MCPD extraction at 2 milligrams per kilogram of paper and 1,3-DCP at 2 micrograms per liter in water extracts.
Paper mills control resin addition rates to maintain cross-linking efficiency while limiting free epichlorohydrin hydrolysis products in finished rolls.
Background mineral oil readings may originate from ambient warehousing air rather than board furnish contamination.

Medium
Evaluating food contact materials relies on physical phase surrogates that replicate actual food interactions. Solid and liquid simulants duplicate the extraction behavior of aqueous, acidic, alcoholic, and fatty foods. Standard migration tests isolate the contact surface area, using a fixed surface-to-volume ratio of 6 square decimeters of paperboard per 1 kilogram of food simulant.
Mineral oil fractions migrate primarily through the gas phase.
Modified Polyphenylene Oxide (MPPO), sold commercially as Tenax, serves as the standard solid food simulant specified in EN 14338 for testing dry and fatty food contact. Because Tenax strongly adsorbs volatile and semi-volatile organic compounds, tests place 4.0 grams of powder per square decimeter directly on the paperboard surface. Exposure at 60 degrees Celsius for 10 days simulates extended shelf storage above ambient temperature, trapping gas-phase MOSH, MOAH, phthalates, and photoinitiators without damaging the porous board structure.

How Does Tenax Simulant Perform under Thermal Stress?
Aqueous and alcoholic foods enter paperboard via capillary action and fiber swelling. Cold water extraction under EN 645 measures short-term release into room-temperature liquids by soaking board strips in pure water at 23 degrees Celsius for 24 hours. Hot water extraction under EN 647 evaluates hot-fill or boiling conditions by soaking board samples at 80 degrees Celsius for 2 hours.
For non-porous coated boards requiring liquid contact tests, EN 1186 specifies alternative fatty food simulants like 95 percent ethanol and iso-octane.
- Cut test specimens into discrete 1.0 square decimeter coupons using a calibrated stainless steel die press.
- Clamp coupons inside double-sided extraction cells to isolate the targeted food-contact surface from reverse-side printing ink layer.
- Apply 4.0 grams of porous polymer adsorbent powder per square decimeter directly onto the board surface.
- Incubate packed test cells inside a climate chamber at 60 degrees Celsius for 10 continuous days.
- Elute adsorbed chemical migrants from the polymer matrix using high-purity diethyl ether under Soxhlet reflux.
- Concentrate solvent extracts down to 1.0 milliliter using a gentle nitrogen stream before analytical injection.
Tenax serves specifically to simulate contact with dry fatty foods.
| Food Contact Category | Standard Simulant Media | Standard Protocol | Conditioning Time & Temp | Targeted Chemical Classes |
|---|---|---|---|---|
| Dry Fatty Foods (Cereals, Pastries) | Modified Polyphenylene Oxide (Tenax) | EN 14338 | 10 days at 60°C | MOSH, MOAH, Photoinitiators |
| Dry Non-Fatty Foods (Salt, Sugar) | Tenax / Paper Adsorptive Media | DIN EN 14338 | 10 days at 40°C | Volatile Organic Contaminants |
| Aqueous & Acidic Foods | Cold / Hot Water Extract & 3% Acetic Acid | EN 645 / EN 647 | 24h at 23°C / 2h at 80°C | Formaldehyde, Heavy Metals, Glyoxal |
| Fatty Foods (Direct Liquid Contact) | 95% Ethanol / Iso-Octane | EN 1186-13 / BfR XXXVI | 10 days at 40°C / 2 days at 20°C | Phthalates, Rosin Compounds, Plasticizers |
Solvent selection directly influences total extraction yield.
Conditioning paperboard coupons with 95 percent ethanol at 60 degrees Celsius for 10 days produces an extraction yield equivalent to direct olive oil contact.
Temperature controls the underlying rate of molecular diffusion.
Using solvent extraction instead of solid-phase adsorption for dry food evaluation overstates gas-phase migration, as solvents dissolve non-mobile structural binders within the board.

Detection
Quantifying volatile and non-volatile chemical migrants requires high-resolution analytical instruments equipped with mass spectrometry. Extract solutions generated from simulant exposure undergo complex cleanup procedures before chromatographic separation, allowing sensitive instruments to reach detection limits comfortably below statutory migration ceilings.
Gas chromatography separates volatile organic fractions in the extract.
Online coupled Liquid Chromatography-Gas Chromatography with Flame Ionization Detection (LC-GC-FID) is the standard method for MOSH and MOAH determination. High-performance liquid chromatography separates mineral oil fractions using a silver nitrate silica gel column, sending MOSH and MOAH cuts into separate GC injection ports. Thermal desorption with GC-MS confirms mass spectrum profiles for C10 to C35 hydrocarbon fractions.
Baseline limits of quantification (LOQ) are set at 0.5 milligrams per kilogram of food for MOSH and 0.1 milligrams per kilogram for MOAH.
Analytical limits of detection define the boundary for all compliance claims.
Liquid Chromatography-tandem Mass Spectrometry (LC-MS/MS) measures polar, non-volatile compounds including primary aromatic amines, bisphenol derivatives, photoinitiators, and PFAS. Electrospray ionization (ESI) operating in multiple reaction monitoring (MRM) mode achieves quantification limits below 0.001 milligrams per kilogram of simulant extract. Fluorinated target suites monitor perfluorooctanoic acid (PFOA), perfluorooctanesulfonic acid (PFOS), and perfluorohexanoic acid (PFHxA) down to parts-per-trillion sensitivity levels.
Silver nitrate chromatography column separation prevents native vegetable waxes from interfering with mineral oil aromatic hydrocarbon signal integration.
Inductively Coupled Plasma Mass Spectrometry (ICP-MS) measures heavy metals leached into water or acidic simulants under EN 12498 and EN 12497 standards. Microwave-assisted acid digestion using ultra-pure nitric acid breaks down organic paperboard residues, freeing bound metallic ions. Analysis determines total concentrations of lead, cadmium, mercury, chromium, arsenic, and aluminum against certified matrix reference calibration standards.
Analyzing heavy metals requires complete matrix digestion with acid.
A 350 grams per square meter folding boxboard carton made with a virgin bleached top liner and a recycled inner furnish provides a clear calculation model. Solid-phase extraction using Tenax over 10 days at 60 degrees Celsius yields an elution volume of 20 milliliters in diethyl ether. Nitrogen gas evaporation concentrates the sample to 1.0 milliliter.
Injecting 1.0 microliter into an LC-GC-FID system gives an integrated MOSH response equivalent to 4.2 milligrams per kilogram of food simulant across the C10-C35 range, while the MOAH signal integrates to 0.35 milligrams per kilogram. Set against the European recommended MOAH ceiling (non-detectable at 0.1 milligrams per kilogram LOQ), this result shows the substrate requires an internal functional barrier film for direct dry food contact.
Screening for Non-Intentionally Added Substances (NIAS) relies on high-resolution gas chromatography time-of-flight mass spectrometry (GC-TOF-MS) and liquid chromatography quadrupole time-of-flight mass spectrometry (LC-QTOF-MS). Non-target screening matches unknown peaks against NIST and Wiley spectral libraries, while structural prediction software models likely chemical formulas for adhesive degradation products, ink byproducts, and paper oligomers.
Analytical chemistry has yet to reach consensus on whether branched alkylated aromatic hydrocarbons identified during non-target screening carry toxicological hazards equivalent to linear MOAH structures.

Dossier
Demonstrating compliance requires building defensible technical files to accompany paperboard shipments. The Declaration of Compliance (DoC) serves as the primary legal instrument certifying adherence to Regulation EC 1935/2004 Article 16. Converters, importers, and brand owners must maintain these technical records to satisfy border customs audits and inspections by national market surveillance authorities.
Declarations of compliance carry binding legal weight.
A complete technical file links finished boxboard roll batch numbers directly to accredited laboratory test reports. Reports must document analytical methods, specific simulants used, exposure surface-to-volume ratios, detection limits, and raw quantitative results. Generic product datasheets, unsigned declarations, or test reports older than two years without re-validation offer no legal defense during enforcement proceedings.
- Substrate Chemical Identification specifies virgin wood fiber species composition, internal sizing chemistries, and mill production lot numbers.
- Analytical Test Certificates document raw laboratory chromatograms, extraction simulants, limit of quantification values, and formal pass outcomes.
- Functional Barrier Efficiency Data proves migration suppression below regulatory thresholds over the declared product shelf life.
- Converter Ink Declarations verify compliance with printing ink exclusion lists and low-migration photoinitiator formulation standards.
- Statement of Intended Use defines explicit temperature ceilings, food contact surface ratios, and permitted food contact types.
Customs inspectors regularly audit these technical dossiers.
Functional barrier certificates confirm that inner plastic laminates, bio-polymers, or water-based dispersion coatings prevent chemical migration from recycled board layers. Oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) values do not prove chemical barrier performance against mineral oils or photoinitiators. Instead, testing under ASTM F1249 or pinhole gas chromatography breakthrough methods verifies barrier integrity over the declared shelf life.
Article 16 of Regulation EC 1935/2004 mandates that documentation trace packaging lots directly to accredited lab test certificates.
Packaging lacking verified documentation faces immediate rejection at port of entry.
Functional barriers prevent transport of volatile contaminants into food.
Test reports lose validity whenever substrate formulations change.
Failing to state a required food-contact restriction on a Declaration of Compliance makes the importer of record directly liable for full inventory seizure and commercial recall costs at customs.

