Calculating Internal Shear Delamination Values to Prevent Board Surface Rupture
Prevent board surface rupture by calculating localized nip and film tension shear forces to ensure total operational stress stays below substrate ZDT values.

Cohesion
Paperboard plies separate along internal failure planes when mechanical stress applied during lamination, varnish curing, or hot foil stamping exceeds the Z-directional tensile capability of the fibrous matrix. In multi-ply folding boxboards, solid bleached boards, and recycled carton substrates, internal bond strength relies on inter-fiber hydrogen bonding, starch retention within the middle layers, and mechanical refining. Mechanical refining increases fiber swelling and surface area, which raises the density of bonding sites across adjacent fiber layers.
When a heavy film lamination or viscous UV varnish cures on the top surface, it contracts and imposes continuous tensile and peel stress across the clay coating and upper bleached fiber layer. If the internal shear resistance of the substrate falls below this localized stress, the sheet splits internally, causing visible blisters, surface skinning, or catastrophic rupture during downstream converting.
Quantifying Z-directional integrity requires distinguishing between total energy absorption and static tensile peak force. TAPPI T 569 utilizes a calibrated pendulum impact hammer to measure the energy in Joules per square meter needed to split an internal fiber network under rapid dynamic impact. ISO 1924-2 and TAPPI T 541 evaluate static Z-direction tensile strength (ZDT) in kilopascals by adhering metal anvils to the board surfaces with double-sided tape and pulling the sample perpendicularly to its plane until tensile failure occurs.
Solid bleached sulfate boards achieve high ZDT through uniform chemical pulping, whereas folding boxboards with mechanical pulp centers exhibit lower energy absorption per unit area due to shorter, stiffer groundwood fibers in the core.
| Paperboard Substrate Grade | Typical Grammage (gsm) | Nominal Caliper (microns) | Scott Internal Bond Energy (J/m²) | Z-Direction Tensile Strength (kPa) | Dominant Delamination Zone |
|---|---|---|---|---|---|
| Solid Bleached Sulfate (SBS) | 300 | 380 | 210 – 260 | 420 – 510 | Sub-surface bleached hardwood layer |
| Folding Boxboard (FBB, Kraft Back) | 350 | 460 | 140 – 180 | 280 – 350 | Interface between top liner and mechanical core |
| Coated Recycled Board (CRB) | 400 | 520 | 95 – 130 | 190 – 240 | Center recycled fiber plies |
| Solid Unbleached Board (SUB) | 330 | 430 | 180 – 230 | 380 – 460 | Softwood unbleached core matrix |
Dynamic impact energy measurements regularly diverge from static perpendicular pull data when evaluating coated surfaces. High-speed converting equipment subjects paperboard to localized shear vectors operating at angle offsets between fifteen and ninety degrees relative to the sheet surface. A substrate exhibiting high static ZDT can still suffer top-layer skinning if the surface coating layer lacks sufficient binder penetration.
Latex migration during board mill drying concentrates synthetic binder at the immediate surface, leaving a starch-depleted layer directly beneath the double clay coating. High-tack inks or heavy plastic film laminates hook into this depleted layer, peeling the top fiber skin clear off the bulk mechanical pulp core under high-speed web tension.
How micro-fibrillated cellulose additives redistribute internal shear stress vectors during rapid moisture desorption remains unquantified across high-speed thermal lamination lines.

Nip
Pressure rolls on film laminators and coater units create sharp stress gradients inside paperboard as the sheet moves through the machine pass. The elastomeric cover on an impression roll compresses against a hard steel roller, creating a pressure profile across the contact zone. As paperboard enters this contact zone, the top layer slows relative to the rigid core, creating horizontal shear stress parallel to the fiber alignment.
High speed combined with high nip force creates severe shear stresses between board layers. If horizontal shear exceeds the internal bond strength, fiber plies split before the adhesive layer even cures.
Viscoelastic deformation within the paperboard matrix amplifies this shear generation. Moisture content acts as a plasticizer for cellulose fibers. At moisture levels above seven percent, the elastic modulus of the middle ply decreases significantly, allowing bulk shear deformation while the drier, stiff top layer resists movement.
Thermal lamination accentuates this physical imbalance. Heat applied to the film side expands surface moisture into steam, which migrates into the central mechanical pulp plies. The resulting moisture gradient reduces internal shear strength right when the sheet faces peak roll compression and bending forces.
Thermal film lamination at 115 degrees Celsius with a 70 Shore A impression roll generates peak localized internal shear stresses reaching 180 kilopascals at a web speed of 80 meters per minute.
Roll cover hardness directly alters the width of the compression zone and the peak pressure reached during running. Soft rubber covers spread the compressive load across a wider zone, reducing peak pressure while extending shear exposure time. Hard rubber rolls concentrate compressive energy into a narrow band, sharping peak pressure and increasing localized shear forces at ply boundaries.
Finisher operators select roll durometer based on board stiffness and caliper, avoiding high pressure peaks on heavy multi-ply boxboards.
- Viscoelastic Ply Slippage occurs when soft central mechanical layers yield laterally under nip compression while rigid outer chemical plies resist movement, splitting the inter-ply starch bond.
- Asymmetric Moisture Expansion Shear develops as heat vaporizes surface water, forcing steam into middle layers and lowering core shear resistance during high-temperature lamination passes.
- Differential Thermal Contraction Pull happens when cooling plastic laminating films contract faster than the paperboard matrix, leaving permanent shear stress across the top fiber layer.
- Hydraulic Barrier Trap forms when liquid adhesives fail to penetrate wet clay coatings, trapping hydraulic pressure that ruptures outer board fibers under roll compression.
Calculations for operational shear generation require evaluating web tension alongside roll force parameters. Web tension pulls the outer sheet skin taut, adding vector components to the horizontal shear created by roll rotation. When combined lamination forces exceed the substrate’s inter-ply strength, micro-void delamination develops inside the central plies, causing visible blister defects and liner separation when finished packages encounter heat sealing processes downstream.

Tack
Surface forces generated during ink transfer, cold foil release, and hot stamping pull directly on the outer layer of paperboard. In wet offset printing, ink tack creates peel forces as the blanket cylinder separates from the sheet. Highly viscous inks run on fast web presses exert pick forces that can peel off the clay coating or split the upper fiber layer.
Modern automatic tack testing uses inkometers to record dynamic film-split resistance in gram-meters. When ink tack exceeds the strength of the top ply, paperboard fibers pull out of the matrix, creating surface debris, print voids, and blanket contamination.
Compliance with TAPPI T 569 specifies a minimum internal bond energy of 150 Joules per square meter to prevent top-ply picking during six-color sheetfed offset press runs using high-tack vegetable-based inks.
Hot foil stamping applies intense heat and pressure over short dwell times, activating release layers while driving hot metal dies into the sheet caliper. As the foil carrier film pulls away, the metalized layer must separate cleanly along die edges. Low foil release tension creates strong peel forces on the substrate skin.
If the board surface bond strength falls below the release pull force, the outer fiber layer tears away with the foil, creating jagged edges and exposing raw fibers around stamped areas.
| Scott Bond Energy (J/m²) | Max Inkometer Tack Rating (1200 rpm) | Max Allowable Hot Foil Pull Force (N/mm²) | Observed Surface Failure Mode |
|---|---|---|---|
| Below 100 | 9.5 | 0.12 | Total top-liner delamination and blanket skinning |
| 100 – 135 | 12.0 | 0.25 | Micro-picking of clay coating and fiber lift |
| 136 – 175 | 15.5 | 0.40 | Clean foil separation with zero fiber tear |
| 176 – 220+ | 18.5+ | 0.58+ | Substrate holds under heavy high-tack solids |
Adhesive green strength creates similar peel forces in cold foil applications. Cold foil adhesives apply via offset units, receiving immediate ultraviolet light curing before the film pulls away. Rapid polymer cross-linking builds instant adhesive peel resistance.
If adhesive cohesion surpasses internal substrate bond strength, the top paperboard layer peels away with the matrix film, destroying surface smoothness across metallic sections.
Substrate mills routinely claim surface skinning occurs solely from improper laminator corona treatment rather than structural weakness within the outer mechanical pulp layer.

Equilibrium
Preventing surface rupture requires calculating the internal force balance where total applied shear forces meet substrate Z-direction resistance limits. Shear forces aggregate across lamination, ink tack, die impression, and temperature-driven film shrinkage. Surface rupture occurs when total applied shear forces exceed the internal bond capacity of the weakest paperboard layer.

Which Shear Calculation Best Predicts Surface Rupture?
Calculating shear loads accurately requires combining static peel forces with dynamic roll pressure forces. Static peel values derived from 90-degree film peel tests provide baseline adhesion metrics, but fail to account for web speed effects. Real-world converting operations use dynamic shear equations that incorporate web speed, impression roll hardness, film modulus of elasticity, and working moisture levels.
Calculating internal shear stress relies on establishing clear force vectors across the web profile. Total internal shear stress equals web-tension shear force plus roll-compression shear force plus film-shrinkage shear force. Web-tension shear force depends on raw web tension per unit width divided by total sheet caliper.
Roll-compression shear force uses the peak nip pressure multiplied by the elastomeric roll cover friction coefficient. Film-shrinkage shear force calculates from the difference in thermal expansion coefficients between film and paperboard, multiplied by temperature change and film elastic modulus.

Deriving the Shear Failure Threshold Equation
The total shear failure threshold formula establishes the operational safety envelope for converting passes. Converting lines operate safely when combined shear forces multiplied by an operational safety factor remain lower than the measured Z-direction tensile strength of the paperboard substrate.
Consider a practical converting operation processing a 350 gsm (450 micron caliper) folding boxboard with a mechanical pulp core. Laboratory testing confirms a Scott Internal Bond value of 145 Joules per square meter, converting to a static Z-direction tensile strength of 290 kilopascals under standardized conditioning. The process pass applies a 12-micron thermal Oriented Polypropylene (OPP) film running at 90 meters per minute, using a 118 degrees Celsius roll temperature and a 75 Shore A impression roll operating at 2.4 megapascals line pressure.
Calculations show web tension contributes 42 kilopascals of horizontal shear force. Roll compression across the 75 Shore A nip zone adds 135 kilopascals of localized horizontal shear along the upper ply interface. Thermal contraction of the cooling OPP film adds 68 kilopascals of continuous shear force across the top layer.
Combining these three values yields a total applied internal shear stress of 245 kilopascals across the upper fiber boundary.
Comparing the calculated total shear stress of 245 kilopascals against the substrate Z-direction limit of 290 kilopascals reveals a narrow 45-kilopascal operating margin. Introducing a 1.25 converting safety factor increases the effective shear requirement to 306 kilopascals. Because 306 kilopascals exceeds the board’s 290-kilopascal limit, running at full line speed under these settings will trigger internal delamination and blister rupture.
Operators reduce line speed to 65 meters per minute and drop roll nip pressure to 1.8 megapascals, lowering total applied shear stress to 188 kilopascals and establishing a safe converting margin.
When film lamination stiffness exceeds the bending stiffness of the underlying board, internal shear stress shifts completely into the top fiber layer.
Extending these calculations to complex finishing lines requires accounting for repeated processing passes. Stacking cold foil application, six-color offset printing, OPP lamination, and heavy embossing onto a single sheet accumulates localized fatigue within inter-ply fiber bonds. Each pass degrades internal bond energy by three to seven percent through physical flexure and thermal cycling.
Calculating shear safety thresholds for multi-pass runs requires applying cumulative bond degradation factors to initial laboratory test values before setting final machine speeds and nip pressures.

Crease
Scoring and creasing paperboard alters internal delamination mechanics by intentionally introducing controlled internal shear failure. Folding a flat board 90 or 180 degrees creates intense tensile forces along the outer surface and high compressive forces along the inner surface. If paperboard remains rigid during folding, outer surface tension splits the clay coating and tears top fibers, creating unsightly cracked edges along box folds.
Creasing matrices prevent surface rupture by forcing internal plies to delaminate cleanly within the creasing zone, allowing middle layers to slide past each other and absorb bending stress internally.
Calculating proper scoring geometry requires matching male creasing rule width and female channel groove dimensions directly to board caliper and ply density. Female channel width formula equals board caliper multiplied by 1.5, plus male rule thickness. Female channel depth equals board caliper.
When rule dimensions match board specifications, creasing rules drive the board into the female channel, inducing localized horizontal shear stress that separates middle mechanical plies without rupturing top chemical fibers or clay coatings.
- Measure board caliper with a calibrated dead-weight micrometer under standard atmospheric conditions to establish exact base physical dimensions.
- Calculate female channel groove width using established multiplier formulas matched to multi-ply fiber orientation and substrate density.
- Select male creasing rule thickness and tip radius to concentrate vertical impression force directly into central core layers.
- Calibrate impression depth on the die-cutting platen to achieve controlled internal ply separation without cutting outer chemical fiber layers.
- Verify score depth and resistance using an electronic crease stiffness tester under controlled relative humidity conditions.
Relative humidity directly controls creasing performance on packaging lines. Dry paperboard below 4.5 percent moisture turns brittle, resisting controlled internal delamination during scoring. Under low moisture conditions, creasing rules cut through fibers rather than separating middle plies, causing severe surface liner cracking when folded.
High moisture board above eight percent turns soft and spongy, absorbing creasing forces without establishing clean internal shear planes. This leads to broad, uncontrolled delamination zones that ruin box squareness during high-speed folding and gluing operations.
| Board Caliper (mm) | Male Rule Width (pt / mm) | Calculated Matrix Width (mm) | Matrix Depth (mm) | Observed Crease Delamination Behavior |
|---|---|---|---|---|
| 0.35 (350 µm) | 2 pt (0.71 mm) | 1.25 | 0.35 | Clean inter-ply shear, zero surface cracking |
| 0.45 (450 µm) | 2 pt (0.71 mm) | 1.40 | 0.45 | Controlled core delamination, sharp fold profile |
| 0.60 (600 µm) | 3 pt (1.07 mm) | 2.00 | 0.60 | Optimal ply displacement, zero clay coat fracture |
| 0.80 (800 µm) | 4 pt (1.42 mm) | 2.60 | 0.80 | Wide internal delamination zone, stable square fold |
Inadequate internal ply delamination inside the scoring channel forces tension to the outer clay coat, producing visible fiber cracking along the box spine.
Matrix selection requires extra clearance when creasing laminated board stocks. Plastic laminating films add elastic memory and tensile strength to the outer surface, increasing resistance to initial creasing penetration. Increasing female groove width by ten percent relative to standard unlaminated calculations prevents film stretching and avoids top-layer skinning along the creasing shoulder.
A creasing matrix channel calculated narrower than substrate caliper forces vertical shear forces into outer liner plies, cracking surface coatings immediately upon folding.

Dossier
Preventing delamination failures across complex supply chains requires translating shear physics into clear procurement specifications and mill verification standards. Standard commercial purchase orders often rely on basic grammage and caliper specifications, ignoring internal bond metrics. Specifying minimum Scott Bond energy values and Z-directional tensile tolerances in board procurement contracts protects buyers from surface delamination failures during finishing.
- Certified Internal Bond Minimums specify mandatory Scott Bond energy values (TAPPI T 569) matching intended lamination, hot foil, and printing processes.
- Conditioning Atmosphere Declarations require test metrics to be verified under ISO 187 standard conditions (23 degrees Celsius, 50 percent relative humidity).
- Cross-Directional Shear Tolerances define minimum allowable ZDT levels along the cross-machine direction to withstand transverse converting stress.
- Surface Ply Pick Resistance Thresholds mandate minimum IGT surface pick values (ISO 3783) to prevent ink-tack skinning on high-speed offset lines.
Receiving inspection routines must verify mill test certificates against incoming batch samples before releasing stock to pressrooms. Atmospheric conditioning of delivered board rolls and sheet pallets is essential prior to testing. Cold board brought into warm pressrooms develops internal moisture gradients as condensation forms on pallet edges.
Testing cold board yields artificially high internal bond numbers that drop sharply as the sheet warms, concealing delamination risks until lamination passes begin.
Including ISO 15754 compliance clauses with mandatory batch-level Scott bond energy certification in paperboard purchasing agreements establishes legal grounds for returning substrate lots that delaminate under standard lamination conditions.

